I/O modules configure the 6100 to your specific needs. Pacific offers a broad selection of modules providing a high degree of flexibility, accuracy and performance. Series 6100 I/O Modules condition, amplify, filter and output high level signals to external data acquisition systems. Modules are selected according to functional and performance requirements for your application.
Voltage & current excitation with remote sensing per channel
Automatic zero & balance
Voltage substitution and two or four step shunt calibration
Gains 1 to 5,000 up to 100 kHz bandwidth with 0.05% accuracy
Programmable low-pass filters
Dual buffered 10 Volt analog outputs
Description
Model 6120 is a two-channel, fully automated, high bandwidth, signal conditioning amplifier and filter with dual inputs. The bridge input has voltage and current excitation, automatic balance, shunt calibration and programmable configuration for ...
The 6129 input module has eight channels each providing excitation for IEPE transducers, programmable AC or DC-coupled differential instrumentation amplifier and low-pass filter. Each channel has a buffered analog output that can be selected for wideband or filtered response.
Using amplifier-per-channel architecture offers the highest accuracy and completely eliminates crosstalk between channels. It may be used to condition signals ...
Voltage & current excitation including remote sense
Gains 1 to 5,000 with 0.05% resolution
50 kHz or 100 kHz bandwidth
Automatic zero & balance
Programmable low pass filters
Voltage substitution gain calibration
Dual buffered 10 Volt analog outputs
Description
The 6131 is a two-channel, fully programmable signal conditioning amplifier and filter. It features a plug-on signal conditioning completion card that is available for strain gage, bridge, RTD, potentiometer, voltage-mode charge, voltage and current transducers. Each channel has a programmable gain ...
Model 6136 is a four-channel, programmable charge amplifier, filter, analog output module with a second input for piezoelectric sensors with integrated electronics (IEPE).
The high-performance charge amplifier can be used to measure dynamic acceleration, pressure, force and strain from piezoelectric ...
Programmable input configuration 1/4, 1/2 & full bridge
Programmable excitation with remote sensing
Shunt & voltage calibration
Automatic zero & balance
Gains 1 to 5,000 with 0.05% accuracy
Buffered 10 Volt analog output
Description
The 6152 input module has four channels of high performance signal-conditioning amplifiers for strain gages and bridge transducers. Each channel has programmable excitation with remote sensing, voltage calibration, local or remote shunt calibration, programmable gain instrumentation amplifier and four-pole low pass filter. Each channel provides a buffered analog output.
Isolated excitation & input with 300 Volts common mode
Plug-in channel configuration & calibration card
Voltage & current excitation with remote sensing
Automatic zero & balance
Voltage substitution, DAC or 2/4 step shunt calibration
Gains 1 to 5,000 with 50 kHz or 100 kHz bandwidth
Four six-pole low-pass filters, optional programmable filter
Dual buffered 10 Volt analog outputs
Description
The 6160 is a two-channel signal conditioning amplifier module with 50 kHz or 100 kHz bandwidth and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current ...
The 6165 is a two-channel instrumentation amplifier module. Each channel has isolated input, 100 kHz bandwidth and two outputs that can be filtered or wideband.
The input is two-wire shielded and is isolated from the outputs, power and control interface. This gives the user complete freedom to ground the input without creating ground loops that introduce noise and offset errors. The isolation provides for ...
Isolated excitation & input with 300 Volts common mode
Voltage & shunt calibration
Gains 1 to 5,000 with 100 kHz bandwidth
Continuously programmable 6-pole low pass filter
Dual buffered 10 Volt analog outputs
Description
The 6168 is a two-channel signal conditioning amplifier module featuring 100 kHz bandwidth and analog outputs. The base board contains both constant voltage with remote sensing and constant current programmable excitation supplies, high-bandwidth instrumentation ...
Signal Conditioning & Data Acquisition
Call: 
