Pacific Instruments, Inc. Pacific Instruments, Inc.
4080 Pike Lane
Concord, CA 94520
www.pacificinstruments.com
(925) 827-9010
salesrequest@pacificinstruments.com
Products > Integrated Conditioning Acquisition & Control Systems > Integrated Conditioning Acquisition & Control System I/O Modules > 6000 Series Digital I/O Modules > Model 6041  


Model 6041, 16-Bit Test Sequencer

Features

  • 16 Digital sequencer outputs
  • Up to 16 time programmable states for each output
  • ±0.01% Time accuracy
  • TTL/CMOS or relay logic
  • 1 Millisecond resolution.

Description

The 6041 is a test sequencer that controls up to 16 digital outputs for activating facility and test equipment. The outputs may be programmed to change state at specific times before, during and after the recording of test data. The 6041-1 version has TTL/CMOS outputs while the 6041-2 version has form C relay outputs.

The 6041 is used to control external equipment in a programmed time sequence. Each of the 16 outputs may be programmed to change state sixteen times at specific intervals with 1 ms resolution. A control input or initiation of the system preview or start operating modes starts the sequence. A second control input stops and resets the sequence. The sequence is also stopped and reset upon reaching its end. The control inputs for the 6041-1 are TTL and optic isolated for the 6041-2.





Overview  · Sequencer  · Output Logic Levels  · Input Logic Levels  · General  · Ordering Information 

Overview

Measurement Type
Digital In
Digital Out
Sequencer


Sequencer

Outputs (6040-1)
16 TTL/CMOS.

Outputs (6040-2)
16 single-pole form C relay.

Sequence
Each output may be programmed to change state up to 16 times.

Delay Time
1 mS to 1 hour. Delays may be cascaded for longer times.

Start
Sequence is started by the 6041's start input, initiation of the system preview mode or initiation of the system record mode.

Stop
Sequence is stopped and reset after the longest programmed delay time or by the stop control input.

Status
Status of the sequencer outputs may be read by including the sequencer's outputs in the scan list.

Connectors (Sequencer)
Input connector is 50-pin Type D, output connector is 50-socket Type D. Mating connectors are supplied.


Output Logic Levels

Output Logic Levels
6041-1 - TTL/CMOS. On is +4.8 Volts minimum; off is +0.15 Volts maximum from 1K Ohm source impedance.
6041-2 - One form C contact rated for 2 A at 30 VDC. Maximum voltage is 220 VDC.


Input Logic Levels

Input Logic Levels
6041-1 - TTL/CMOS. Off is less than +0.8 Volts; on is greater than +2.0 Volts. Protected to 50 Volts.
6041-2 - Optic isolated, off is less than 1.45 Volts; on is greater than 3.70 Volts. Input impedance is 360 Ohms. Protected to 50 Volts.


General

Mounting
Occupies one slot in Series 6000 enclosures.

Connectors (General)
50-pin type D connector inputs and 50-socket type D connector for outputs. Connectors are on the front and mates are supplied.

Temperature
0 to +50 ºC

Humidity
Up to 95% without condensation.


Ordering Information 

Ordering Information
6041-1 - 16-Bit Sequencer, TTL/CMOS In, CMOS Out.
6041-2 - 16-Bit Sequencer, Optic Isolated In, Form C relay Out.

Pacific Instruments, Inc. · 4080 Pike Lane · Concord, CA 94520 · www.pacificinstruments.com