Products > Integrated Conditioning Acquisition & Control Systems > Integrated Conditioning Acquisition & Control System I/O Modules > 6000 Series Analog I/O Modules > Model 6014  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Model 6014, 8-Channel Accelerometer Amplifier-Filter-Digitizer





Features

  • AC or DC coupled inputs, IEPE transducers
  • 2 to 20 mA current excitation
  • Gains 1 to 5,000 with 0.05% accuracy
  • Automatic zero & gain calibration
  • Four pole, low pass filter
  • Up to 10 kS/s per channel with 16-bit resolution
  • Two alarms with programmable upper & lower limits

Description

The 6014 input module has eight channels, each with AC or DC coupled programmable gain instrumentation amplifier, low pass filter and sample and hold. The high level outputs are multiplexed and digitized to 16 bits then output to the 6000 data bus. Each channel has a 2-20 mA current source for powering low impedance, voltage mode charge transducers.

The 6014 is used with low impedance, piezoelectric transducers and low or high-level voltage signals. The input may be AC coupled for amplifying dynamic signals without the DC signal component or by changing jumpers it becomes a DC-coupled instrumentation amplifier.

Voltage substitution is provided for channel gain calibration utilizing an external voltage standard. A calibration attenuator enables the voltage standard to be used on its highest accuracy ranges and has a post-attenuator output for calibration. Using Pacific's PI660 software zero and gain calibration and correction are automatic.

A four-pole, low-pass filter uses easily changed plug-in modules to set bandwidth. Either the wideband or filtered output may be digitized and sent to the 6000 data bus. Two programmable alarms with upper and lower limits are checked each time the outputs are digitized. The high-level analog outputs provide a means to independently monitor or record each channel.






Overview  · Input  · Excitation/Transducer Power  · Amplifier  · Filter  · Digitizer  · Calibration  · Mechanical  · Ordering Information 

Overview

Measurement Type

ICP/IEPE

Analog Bandwidth

1 kHz

Excitation/Transducer Power

ICP

Filter

4-Pole

Sample Rate (Digitizer)

Up to 10 kS/s

Analog Output

Monitor Output


Input

Configuration

8 channels, differential, 2-wire with shield.

Range

±100 mV to ±10 Volts (±2 mV to ±10 Volts with reduced bandwidth).

Type (Input)

Jumper selection of AC or DC input coupling.

DC Coupled

50 Megohms, shunted by 1,000 pF.

AC Coupled

100K Ohms

Protection

±50 Volts differential, ±30 Volts common mode.


Excitation/Transducer Power

Level

2 to 20 mA set by resistor for each channel. Factory set to 6 mA. Compliance is 24-28 Volts. Requires optional supply for the enclosure.

Supply

Internal on Series 6000 enclosures.


Amplifier

Gain

Programmable 1-5000, in 1, 2, 3, 5 steps, with ±0.05% accuracy.

Gain Stability

±0.01%, ±0.005%/ºC.

Bandwidth (DC)

DC to 5 kHz for gains 1 to 100. DC to 1 kHz for gains above 100 (-3 dB).

Bandwidth (AC)

0.5 Hz to 5 kHz for gains 1 to 100. 0.5 Hz to 1 kHz for gains above 100 (-3 dB).

Linearity (Amplifier)

±0.01% for gains 1 to 1,000, ±0.02% for gains above 1,000.

Common Mode

60 dB plus gain in dB up to 110 dB, DC to 60 Hz.

CM Voltage

±10 V

Zero (Amplifier)

Automatic to ±1 mV RTI, ±0.5 mV RTO.

Zero Stability

±2 µV RTI, ±1 mV RTO. ±1 µV/ºC RTI,
±0.2 mV/ºC RTO. Short term: ±2 µV RTI,
±0.04 mV RTO for 8 hours.

Source Current

±2 nA, ±0.01 nA/ºC.

Noise (10 Hz)

0.5 µV peak, RTI.

Noise (1 kHz)

1.5 µV peak, RTI

Recovery

800 µS to ±0.1% for 10X overload to ±10 V.


Filter

Type (Filter)

Four-pole, low-pass Butterworth.

Frequency

Plug-in, 40 Hz to 5 kHz, 1 kHz supplied.

Noise

2 mV peak, RTO.

Other

Other filter characteristics and cut offs are available.


Digitizer

Sample

Simultaneous sample and hold with ±50 nS channel-to-channel. Droop is less than ±0.005%.

Resolution

16-bits, two's complement output.

Sample Rate

Up to 10 kS/s per channel
Up to 10
kS/s

Digitizer Linearity

±2 LSB (±0.006%)

Continuity

Monotonic to 15 bits.

Alarms

Two alarms each with upper and lower limits that are programmable from negative to positive full scale. Limits checked on each ADC sample.


Calibration

Voltage Substitution

Alternate input for external voltage standard. Programmable attenuation steps of 1, 0.1, and 0.01 with ±0.02% accuracy. Output of attenuator is provided for calibration.

Zero Calibration

Amplifier input disconnected and shorted.


Mechanical

Mounting

Occupies one slot in Series 6000 enclosures.

Connectors

Input connector is 50-pin Type D. Connectors are mounted on the front and mates are supplied.

Operating Temperature

0 to +50 ºC


Ordering Information 

Ordering Information

6014 - 8-Ch Accelerometer Amplifier-Filter-Digitizer.
6081 - Screw Terminal Adapter.


 DOWNLOADS 

Model 6014
(PDF, 91KB)



 Complementary to Model 6014 


Model 6039
Model 6039 8-Channel Strain/Bridge Transducer Amplifier - Filter-Digitizer


Model 6044
Model 6044 32-Bit Discrete Input/Output with Alarms

© 2024, Pacific Instruments, Inc. Catalog IndexPrivacy PolicySite Map