Products > Transient Recording Systems > Transient Recording Modules > Model 584X  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Model 584X, Transient Recording I/O Modules



Features

  • Record fast events, up to 10 MS/s
  • One pre-trigger and two post-trigger sample rates
  • Rugged 3 or 16 channel, battery operated enclosures
  • 16 Channel A/C powered laboratory enclosures
  • Ethernet interface with Windows software
  • Dual inputs, bridge and ICP
  • Programmable for 1/4, 1/2 and full bridges
  • Voltage & shunt calibration
  • Automatic, hands-off operation
  • Analog output for external recording

Description

Individual channel modules that plug into the 5800 enclosures condition, amplify, filter, digitize and store the transducer signals. Simultaneous sampling provides excellent time correlation between channels and external events. The digitizer is available with 14, 16 or 24-bit resolution and sample rates up to 10 Million samples per second.

Data acquired by the 5800 is digitized and recorded in non-volatile, solid-state memory. It records calibration, pre-trigger and post-trigger data. In a typical test scenario recording of pre-trigger data is initiated by a TTL input, program instruction, or automatic sequencer. A TTL input or on-board discriminator triggers post trigger data recording.

The quantities and sample rates of pre and post-trigger data storage are programmable, enabling the 5800 to be configured according to the characteristics of the data being acquired. Sample rate can be changed during acquisition without interrupting data flow to capture high-speed events, yet have sufficient memory space to record long-term effects. The 5800 can be configured for multiple records, each using the same pre and post-trigger sampling profile. Data is debriefed and transferred to permanent storage by the Ethernet interface.

Each channel has two inputs: one for bridges, voltage, RTDs, potentiometers and thermocouples; the other AC coupled with current excitation for transducers with built-in electronics. Signal conditioning includes programmable excitation and completion for 1/4, 1/2 and full bridge, AC-coupling, automatic balance, voltage and four-step shunt calibration, programmable gain and a four frequency, eight-pole filter.






Input  · Bridge Input  · IEPE Input  · Voltage Excitation / Transducer Power  · Amplifier  · Filter  · Calibration  · Digitizer  · Memory  · Trigger  · Ordering Information 

Input

Configuration

Dual Input, Bridge and ICP/IEPE with analog outputs

Input Stability

±0.1% for 8 hours, ±0.01%/ºC


Bridge Input

Bridge Connector

Miniature, 8-pin, threaded, round DIN. 5871ST has six-position terminal strip.

Bridge Balance

Automatic, may be turned off without affecting the setting.

Balance Range

2 mV/V for 350 Ohm bridge and is setable by resistor from < 0.1 mV/V to > 10 mV/V.

Balance Resolution

0.025 %

Balance Accuracy

±0.1% of range, ±1 mV

Bridge Completion

Programmable completion is installed for 350 Ohm and 120 Ohm 1/4 and all 1/2 bridge circuits. The 1/4 bridge completion resistors are in resolderable sockets and may be replaced to accommodate other values.


IEPE Input

IEPE Input

AC coupled input (< 2.25 Hz) to accept charge transducer with integral or line preamplifier.

IEPE Connector

BNC

IEPE Excitation

6 mA, ±10% (range is 1 to 20 mA).

IEPE Input Impedance

100K Ohms

AC Coupling

Programmable high pass filter, 2.25 Hz. Input impedance is 100K Ohms.

IEPE Filter

Selectable low pass input filter, 16 kHz.


Voltage Excitation / Transducer Power

Voltage Excitation

0 to 12 Volts in 1-Volt ±0.1% steps. 50 mA, limited to 70 mA maximum.

Voltage Excitation Regulation

±0.2% over the input voltage range and no load to full load.

Voltage Stability

±0.1% for 8 hours, ±0.01%/ºC.

Voltage Monitor

Excitation voltage and current is digitized output and recorded. Accuracy is ±0.1%.


Amplifier

Input Range

±10 mV to ±10 Volts full scale.

Gain

Programmable steps 1, 2, 3, 5, 10, 20, 30, 50, 100, 200, 300, 500 and 1,000.

Gain Stability

±0.02% for 8 hours, ±0.005%/ºC.

Gain Linearity

±0.02 %

Input Impedance

25 Megohms shunted by 500 pF.

Input Protection

±50 Volts differential or common mode.

Common Mode

60 dB plus gain in dB to 110 dB minimum for 350 Ohm source unbalance, DC to 60 Hz.

CM Voltage

±10 V

Zero Stability

±5 µV RTI, ±1 mV RTO at constant temperature. ±1 µV/ºC RTI, ±0.2 mV/ºC RTO.

Noise

10 µV RTI plus 1 mV RTO RMS.

Bandwidth

5841/43 - 100 kHz. Slew rate is 5 V/µS.
5842/44/45/46 - 500 kHz for gains below 100, 300 kHz for higher gains. Slew rate is 15 V/µS.


Filter

Filter Type

5841/42/44/45/46 - Eight-pole, Bessel, low-pass (48 dB/octave terminal slope).
5841/43 - Standard is 5 kHz, 10 kHz, 20 kHz, 50 kHz (-3 dB) and wideband.

5842/44/45/46 - Standard is 10 kHz, 20 kHz, 50 kHz, 100 kHz (-3 dB) and wideband. Other filter frequencies are available on request.


Calibration

Voltage Calibration

Three ranges, ±10 Volts, ±1 Volt and ±100 mV. 0.025% of range (12-bits) of range with ±0.25% Accuracy.

Shunt Calibration

Four-step shunt calibration. Resistor values of 150K, 75K, 15K, and 7.5K ohms give 0.583, 1.16, 5.77, and 11.4 mV/V for a 350 Ohm bridge, ±1%. Resistors are mounted in resolderable terminals. Alternate values may be specified.


Digitizer

Sampling

One pre-trigger and two post-trigger sample rates per record.

Rates

5841: 1M, 500K, 200K, 100K, 50K, 20K, 10K, 5K, 2K, 1K, 500, 200, 100, 50, 20 and 10 S/s.
5842: 2M, 1M, 500K, 200K, 100K, 50K, 20K, 10K, 5K, 2K, 1K, 500, 200, 100, 50, and 20 S/s.
5843: 200K, 100K, 50K, 20K, 10K, 5K, 2K and 1K S/s.
5844/45/46: 10M, 5M, 2M, 1M, 500K, 200K, 100K, 50K, 20K, 10K, 5K, 2K, 1K, 500, 200 and 100 S/s.

Resolution

5843 - 24-bits
5841 & 5846 - 16-bits
5842, 5844 & 5845 - 14-bits

Correlation

1 nS sample to sample, 50 nS channel to channel.

Linearity

5841 - 3.5 LSB
5842, 5844, 5845 & 5846 - 2.5 LSB


Memory

Type

CMOS, with power back up for 40 hours.

Size

3.5M words (24-bit) to 8M words (14 or 16-bit)

Records

Programmable pre and post-trigger data in 4096 word blocks. Multiple records without debriefing.

Write Protect

Enabled on power up and after recording data. Must be cleared before recorded data can be overwritten.


Trigger

Sources

External (TTL input), internal start or Ethernet program command.

Delay

0 to 60 seconds with 1 microsecond resolution.

Internal Start

Programmable full scale with 0.4% resolution. First channel triggers all channels in recorder group.


Ordering Information 

Ordering Information

5841 - Transducer Recorder Module, 1 MS/s, 16-bit, 4M storage.
5842 - Transducer Recorder Module, 2 MS/s, 14-bit, 1M storage.

5843 - Transducer Recorder Module, 200 KS/s, 24-bit, 3.5M storage.

5844 - Transducer Recorder Module, 10 MS/s, 14-bit, 8M storage.

5845 - Voltage Recorder Module, 10 MS/s, 14-bit, 8M storage.

5846 - Transducer Recorder Module, 10 MS/s, 16-bit, 8M storage.

5847 - Voltage Recorder Module, 10 MS/s, 16-bit, 8M storage.


 DOWNLOADS 

Series 5800
(PDF, 382KB)


© 2024, Pacific Instruments, Inc. Catalog IndexPrivacy PolicySite Map